300 m³/h desktop HEPA extractor for laser beauty devices, soldering, moxibustion and lab smoke
Purpose-built for light smoke, dust and odors — laser beauty devices, soldering, moxibustion, electronics rework and lab work. HEPA 13 + activated-carbon filtration captures both the fine particles and the odor, in a footprint that sits on any desk or treatment bench.
Laser hair removal, tattoo removal and skin-treatment devices vaporize hair, skin and ink into a fine plume. The HEPA 13 + carbon stage captures the particles and odor, keeping the treatment room clean.
Soldering-iron stations, solder-pot dipping and small wave soldering produce fine solder fume. The 12-11 is built for exactly this — quiet enough to sit at the bench.
Moxa smoke is dense and pungent. The activated-carbon VOC stage adsorbs the odor while the HEPA stage removes the particulate, for a comfortable treatment or clinic space.
Small laser markers, 3D-printing enclosures, soldering classes and electronics training — a compact, low-noise extractor that fits any desk.
| Specification | Value |
|---|---|
| Airflow | 300 m³/h |
| Power | 350 W |
| Noise | ≤65 dB |
| Dimensions (W×D×H) | 300×500×420 mm |
| Weight | 18 kg |
| Inlet | Ø100/75 mm |
| Outlet | Ø100 mm |
| Filtration | 7-stage HEPA type (consumable) |
| Speed control | Stepless |
| Voltage | 220/230/110 V · 50/60 Hz |
| Certification | CE · 12-month warranty |
Primary filter and secondary fine-particle filter trap coarse dust, hair and larger debris before it reaches the finer stages.
Primary and secondary fiber filters progressively capture mid-size particles and extend the life of the HEPA stage.
A combined HEPA 13 + activated-carbon stage removes fine particles down to 0.3 μm and adsorbs odors and VOCs — the plume and the smell.
The 12-11 is a consumable-type (HEPA) extractor — filters are replaced, not washed, unlike our ESP models. That keeps maintenance simple: swap the filters when airflow drops or odor returns, and you're back to full performance.
Filter life depends on usage. Light daily use — a treatment room or soldering bench — typically runs 6–12 months between replacements. Heavy moxibustion or high-volume soldering shortens that interval. Replacement filter sets are available from Filters & Accessories.
Washable alternative: If you'd rather not buy disposable filters, the 12-1 ESP extractor uses a washable electrostatic cell with only cheap pre-filters to replace — a lower long-term running cost for higher smoke loads.
Can it handle laser beauty device smoke?
Yes — HEPA 13 + activated carbon captures the fine particles and odor from laser hair removal, tattoo removal and skin-treatment plume. It's our recommended compact extractor for aesthetic and beauty laser devices.
Is the 12-11 washable?
No. It's a consumable HEPA unit — filters are replaced when loaded. For a washable ESP unit, see the 12-1.
What's the difference between the 12-11 and the 12-1?
The 12-11 is smaller (18 kg vs 55 kg), quieter-duty (300 vs 500 m³/h) and HEPA-consumable. The 12-1 is an ESP washable unit with higher airflow — better for heavier or continuous smoke.
Does it work on 110V?
Yes — a 110V / 60 Hz variant is available for North America, alongside 220–230V / 50–60 Hz.
Can I adjust the suction?
Yes, stepless speed control lets you dial airflow to match the task — low for quiet soldering, higher for dense moxa or treatment plume.
Tell us your application — beauty laser, soldering, moxibustion or lab — and we'll confirm the 12-11 is right for you and send pricing within 24 hours.
See airflow, filtration type and application fit side by side.
Compare All Models →